Walkera V100D01

Walkera V100D01 Helicopter

 

RC Pro Setup Guide by: Tom Zadar

 

Setup for the Walkera V100D01 – RX2441V Receiver – Walkera WK-2801 Pro Transmitter.

*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*

 

Step 1. Select a new model (or reset a model)

Step 2. COMPTB 2401 and STICK to MODE2

Step 3. REVERS – 1R, 2R, 3N, 4N

Channel 1 is ELEV and channel 2 is ALIE.

Make sure the throttle trim is set all the way down. Default is center.

 

D/R and Expo

If you want Expo and D/R set COMPTB to 2801 and assign a hot key for Expo & D/R.

Then set COMPTB back to 2401.
To do this go into 2801 mode and go into the Expo, D/R screen. Then push down
at the same time the UP and DN buttons. A menu will pop up called
Hot Keys. Select the button you want to assign it to then hit ENT.
Now go back to mode 2601 or 2401 and the hot key (s) you set will be there.
This trick will work for almost all menus like throttle, pitch, gyro gain,
subtrim, etc…
To bring up your hot key you need to hold down the left EXT button and keep it down then
press the hot key button you assigned that you want.
That’s it, you can now fly the V100D01.

You need to know this. When you plug in the battery you will get 2 quick beeps, then turn on the TX and wait for it to bind.
Now wait for 3 beeps from the tail motor and in a 2-3 seconds and you will get 3 beeps from the main motor also.
Now you are ready to fly.

 

DR&EXP

Set D/R and EXPO to your personal preference.

 

Standard Settings

ELEV D/R = 70%  EXP +30%

AILE D/R = 70%  EXP +30%

RUDD D/R = 100%  EXP LIN

 

Beginner Settings

ELEV D/R = 50%  EXP +30%

AILE D/R = 50%  EXP +30%

RUDD D/R = 100%  EXP LIN

 

Ultra Beginner Settings

These settings are for hovering and slow flight only. These settings have very low servo travel which will make the controls less responsive to stick input if you need to tame down the controls even more.

ELEV D/R = 30% EXP -10%

AILE D/R = 30% EXP  -10%

RUDD D/R = 100% EXP +20%

 

 

For more D/R and EXPO settings and information see my post here:

Dual Rate and Expo Settings

http://www.rcproreviews.com/gyro-receiver-dual-rate-expo/

 

 

Walkera V100D01 RX-2441V Settings

Factory settings are 11:30 o’clock for RUDD, 12 o’clock for ELEV and ALIE, and 10 o’clock for ELEV-ALIE Ext.

I was first using 1 o’clock for RUDD, ELEV and ALIE turned all the way up (Max), and 12 o’clock for ELEV-ALIE Ext.

Then I went to 1 o’clock for RUDD, 3 o’clock for ELEV and ALIE, and
12 o’clock for ELEV-ALIE Ext.

My current settings are now 1 o’clock for RUDD, 2 o’clock for ELEV and ALIE, and ELEV-ALIE Ext. turned all the way up (Max).

I have found that ELEV-ALIE Ext will max out at past 1 o’clock as the
servos are maxed out and can’t move anymore.

 

 

Walkera V100D01 Helicopter

RX2441V Settings – Factory Settings (Defaults) 11:30 o’clock for RUDD, 12 o’clock for ELEV and ALIE, and 10 o’clock for ELEV-ALIE Ext.

 

Walkera V100D01 Helicopter

RX2441V Settings – My current settings are now 1 o’clock for RUDD, 2 o’clock for ELEV and ALIE, and ELEV-ALIE Ext. turned all the way up (Max).

 

 

Here is a HD settings video I made.
Note: Set to STICK MODE 2 not MODE 1. It defaulted to Mode 1 as I loaded the model.

 

Walkera V100D01 TX Settings for WK-2801 Pro TX

 

 

 

 

“My text, pictures and videos are Copyright 2009 – 2017 Tom Zadar”